Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Folsom Homeowners
Chimney repair in Folsom is a job you want done right the first time. A cracked crown, failing flashing, or deteriorated liner isn’t something that fixes itself, and waiting usually turns a few hundred dollars of masonry work into a full rebuild. Alan Decker and the crew at Chimney Sweep Folsom handle the full stack: sweeping, venting, and structural repair, all under one roof. We work with trade-grade materials from brands like DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield because what goes inside your flue matters as much as what shows on the outside. If you’ve got a fireplace or wood stove that’s acting up, call (833) 589-9896 and we’ll tell you exactly what’s going on.
Key Takeaways
- Full-service repair: We diagnose and fix structural chimney problems, not just sweep and walk away.
- Trade-grade materials: We install DuraFlex liners, HeatShield resurfacing, and Gelco, Famco, and Copperfield caps and ventilation hardware.
- Dryer vent cleaning included: One phone call covers all your home’s exhaust and venting hazards.
- Free estimates: Call (833) 589-9896 for an honest assessment with no obligation.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Installation
Chimney Cap Installation is the single most cost-effective way to prevent water damage, animal entry, and downdrafts in a masonry chimney. A properly sized cap keeps rain from soaking into your flue liner and brickwork, while a mesh screen blocks birds, squirrels, and debris from nesting inside. For Folsom homeowners, the cost typically ranges from $250 to $600 depending on the cap style, material, and whether custom sizing is required. We install caps from Gelco and Famco, both commercial-quality manufacturers whose hardware is built to outlast the bargain caps you’ll find at big-box stores. Every installation includes a check of the flue opening to confirm the cap is matched to your chimney’s actual dimensions.
Cap Sizing and Fit
A cap that doesn’t fit creates more problems than it solves. We measure both the flue tile opening and the crown before recommending a cap, because a tight seal is what keeps rain out and a secure mount is what keeps the cap on during Folsom’s winter wind storms. Custom-fabricated caps are available when standard sizes won’t work.
Animal and Debris Protection
Squirrels in Folsom will find any opening larger than a quarter. The mesh screening on our caps is sized to keep rodents and birds out while still allowing proper draft, and we’ll check for existing nesting material or debris during the install.
Chimney Cap Replacement
Chimney Cap Replacement comes up when an existing cap has rusted through, blown off, or been damaged by animals trying to get in. In Folsom, we replace caps that have failed at the base plate, lost their mesh screening, or started restricting airflow because of creosote buildup. Replacement typically runs $200 to $550, which includes removal of the old cap, inspection of the flue opening, and installation of a factory-matched replacement from Gelco or Famco. If the old cap took the crown with it when it came loose, we’ll flag that on the spot and give you a separate quote for the crown work rather than hiding it in the cap price.
When a Patch Won’t Cut It
A rusted cap cannot be repaired in any way that lasts. Once the base plate or spark screen has corroded, the metal is compromised throughout, and patching just buys you one more season. Replacement is cheaper than the water damage and flue deterioration a failed cap allows.
Matching Your Existing Setup
Some Folsom homes have multi-flue chimneys, and replacement means matching the cap to both flues or installing a full-width cap that covers the entire crown. We’ll show you the options and let you know what the existing cap was doing wrong before we replace it.
Chimney Liner Installation
Chimney Liner Installation is what protects your home from the heat and gases moving through the flue. When the original clay tile liner cracks, shifts, or was never installed to current code, a new stainless liner becomes the safe path for exhaust. In Folsom, liner installation typically runs $1,800 to $4,200 depending on flue height, liner diameter, and accessibility. We install DuraFlex liner systems, which are made from 316L stainless steel and meet the code requirements for wood-burning and gas appliances. A liner isn’t a place to cut corners, and we don’t. The liner gets sized to the appliance, insulated where code requires, and connected with fittings that are built for the temperatures your flue actually reaches.
Pre-Liner Camera Inspection
Before any liner goes in, we run a camera through the existing flue to confirm the route is clear and the old liner isn’t hiding damage that will compromise the new one. If there’s a problem, you’ll see it on the monitor with your own eyes before a dollar is spent.
DuraFlex and Code Compliance
DuraFlex liners are listed to UL 1777, which is the standard your local building inspector will look for. When we size and install the liner, it’s done to pass inspection, not just to look right. For older Folsom homes with unlined masonry chimneys, a DuraFlex retrofit brings the chimney up to the current standard for burning wood or venting gas.
Chimney Flashing Repair
Chimney Flashing Repair addresses the joint where the chimney meets the roofline, which is the most common source of chimney-related leaks in Folsom. Flashing fails because the sealant dries out, the metal separates from the masonry, or the original install was done with materials that never should have been up there in the first place. Typical flashing repair runs $400 to $900 depending on how much of the existing flashing can be salvaged and how steep or high the roof is. We replace failed flashing with new metal, tool the sealant properly into the masonry joint, and don’t caulk over rust to make it look fixed. When the flashing goes, the water follows the chimney down into the attic and through the ceiling, so this is a repair that pays for itself quickly.
Leak Diagnosis Before Repair
Not every chimney leak is flashing. Sometimes it’s the crown, sometimes it’s a porous brick face, and sometimes water is getting in at a completely different spot and migrating to the chimney chase. We trace the leak back to its source before we touch anything, because replacing flashing that wasn’t the problem is wasted money.
Masonry Step Flashing vs. Counterflashing
Older Folsom homes often have step flashing that’s embedded into the brick courses, which is good when it’s intact but bad when the mortar joints have opened up. We repair or replace both the step flashing and the counterflashing as a matched system so the repair holds together rather than failing at the seam.
Chimney Crown Repair
Chimney Crown Repair fixes the concrete or mortar slab that caps the top of the chimney structure. The crown is your chimney’s umbrella, and when it cracks, water gets into the brickwork below the roofline where you can’t see it. Crown repair in Folsom generally runs $350 to $1,000 depending on how much of the crown needs to be rebuilt. Small cracks get sealed with a flexible crown coat that moves with the weather. Larger failures mean forming and pouring a new crown with the proper overhang and drip edge. When we see a crown that’s been slathered in tar or roof cement by a previous repair, we remove all of it and start over with the right materials.
Crown Coat vs. Full Repour
A hairline crack in an otherwise sound crown is a candidate for a crown coat sealant, which is the lower-cost path. A crown that’s spalling, has sections missing, or was poured too thin needs a full repour. We’ll show you which one you have and why.
Drip Edge and Overhang
Most failed crowns in Folsom failed because they were poured without the proper overhang past the brick face and without a drip edge cut into the underside. A correct crown directs water off the chimney entirely. We form our crowns with both features so the repair doesn’t just replace the old problem, it eliminates it.
Chimney Repair Companies
Chimney Repair Companies in Folsom range from one-person sweep operations to full-service masonry contractors, and the difference shows up in what happens after the inspection. Some companies sweep and then hand you a written estimate for work they can’t actually do. Chimney Sweep Folsom is a full-service repair company, so when Alan Decker’s crew finds a problem, the same team that found it does the fix. We don’t subcontract our repairs out, and we don’t send a salesperson to do a technician’s job. The person who runs your camera inspection is the person you’ll see again on repair day.
How We’re Different
We’re trade-credentialed in HeatShield application, which means we can resurface a damaged flue liner when others would tell you a full reline is your only option. Between HeatShield resurfacing and DuraFlex relining, we have two paths to a safe flue, and we’ll tell you honestly which one fits your chimney and your budget.
One Call Covers It All
You don’t need separate contractors for the fireplace, the chimney, and the dryer vent. We sweep, repair, and clean dryer vents, so the exhaust and venting hazards in your home are all handled by one team that actually understands how they interact. Your dryer vent is a fire risk hiding in plain sight, and we include it in the conversation rather than treating it as an upsell.
Chimney Masonry Repair
Chimney Masonry Repair covers the brick, mortar, and stone structure of the chimney itself, distinct from the liner, cap, or flashing. In Folsom, masonry work typically ranges from $500 for spot tuckpointing to $3,000 or more for partial rebuilding of a chimney that’s failing structurally. We also serve nearby areas with Orangevale Chimney Repair services. We do both. The most common job is repointing, which means grinding out deteriorated mortar joints and packing them with fresh mortar that matches the strength and color of what’s there. The less common but more serious job is rebuilding sections where the brick itself has spalled and crumbled. A chimney with compromised masonry is a structural hazard, and we take it seriously.
Matching Mortar and Brick
Old mortar and new mortar are not the same product. Mortar that’s harder than the surrounding brick will destroy the brick over time, which is why we match both strength and color to your existing masonry. In Folsom’s older neighborhoods, we work with brick patterns and mortar tints that blend rather than stand out.
When Masonry Failure Is Structural
A leaning chimney, a bulging face, or cracks that run through the brick rather than just along the mortar joints indicate structural failure, not cosmetic wear. We’ll tell you plainly when a chimney needs a partial rebuild, and we’ll also tell you when the masonry can be repaired and the chimney will serve you for another twenty years.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We stock and install materials from six recognized professional chimney-industry brands because we’d rather put proven hardware in your home than whatever’s cheapest at the supply counter. On the cap and ventilation side, we work with Gelco and Famco, both of which make caps, dampers, and termination hardware that are built for long-term exposure and sized to real flue dimensions, not universal-fit guesses. Olympia Chimney supplies liners and accessories we use on gas appliance venting jobs, and Copperfield makes the termination caps and chase covers we trust for factory-built fireplaces.
On the liner and resurfacing side, we install DuraFlex stainless liner systems for code-compliant flue upgrades and retrofits, and we’re certified to apply HeatShield, the resurfacing system designed to restore aging flue liners without a full tear-out. Whether you have a manufacturer-specific cap that was installed when the house was built or a bare clay tile flue that’s never been touched, we can match the right replacement or upgrade to what you already have. Professional-grade materials, not hardware-store substitutes.
Signs You Need a Pro Right Now
- Water stains on the ceiling or walls near the chimney. Water is getting in somewhere, and it’s usually the flashing, the crown, or the brick face. Each of these has a different fix, and guessing wrong means paying twice. A pro will find the actual entry point.
- Mortar bits or brick chips on the ground at the base of the chimney. That spalling is the chimney shedding its outer layer, and it only accelerates once it starts. Masonry repair now stops the damage before the structure itself is compromised.
- Visible smoke in the room when the fire is lit. That’s a draft problem, and draft problems are usually caused by a restriction in the flue or a chimney that’s not tall enough to overcome the house pressure. Both are fixable, but not by ignoring them.
- A strong smell of smoke or soot when the fireplace isn’t in use. That downdraft is pushing exhaust back into your living space. It’s often a cap issue, and the fix is straightforward once the cause is confirmed.
- Visible cracks in the crown or rust on the cap. The crown and cap are your chimney’s first line of defense against water. When they fail, everything below them fails faster. Repairing them early is the least expensive chimney work you’ll ever do.
Our Process, Step by Step
- 1
Initial phone conversation. You tell us what you’re seeing, what the previous sweep found, or what an inspector flagged on a home purchase report. We’ll ask the right questions to get a read on the problem before we ever show up.
- 2
On-site inspection. Alan Decker or a senior tech comes out and looks at the whole chimney, not just the part that’s complaining. We run a camera through the flue when the situation calls for it, and we check the crown, cap, flashing, and masonry in one pass.
- 3
Straightforward findings. You get a plain-language explanation of what’s wrong, what has to be fixed now, and what can wait. You’ll see the camera footage yourself. Nothing gets recommended without evidence you can look at.
- 4
Repair or installation. When you approve the work, we schedule it and get it done with the right materials, installed to the manufacturer’s spec and current code. The crew that diagnosed the problem does the repair.
- 5
Post-work verification. After the repair, we verify the fix with a follow-up check of the flue and the structure. You get told what was done, why it was done, and what to watch for going forward. No mystery invoices.
How Much Does Chimney Repair Cost in Folsom?
Chimney repair costs in Folsom track the scope of the problem. A cap replacement runs $200 to $550, flashing repair runs $400 to $900, and crown repair runs $350 to $1,000. Liner installation is the big-ticket item at $1,800 to $4,200, and masonry repair lands between $500 for spot work and $3,000 or more for partial rebuilds. Several factors move the price: the height and pitch of your roof (access drives labor), the condition of the existing materials (deteriorated brick takes longer to work with), and whether the repair requires custom fabrication or off-the-shelf parts.
To avoid overpaying, get the camera inspection before you commit to anything. A flue that’s actually fine doesn’t need a liner just because a sales tech says it does, and you should be able to see the proof either way. Also be wary of quotes that bundle a new liner, new crown, and new cap without explaining how each problem was diagnosed independently. A free estimate from us means we tell you what’s actually wrong, what it costs to fix, and what can safely wait. No pressure, no scare tactics, just the facts as the camera and the masonry show them.
Our Service Area Near Folsom
We serve Folsom and the surrounding communities throughout the greater Sacramento foothills. You’ll find us working in home chimneys from Roseville to Citrus Heights, and everywhere in between, including Rocklin, El Dorado Hills, Orangevale, Antelope, North Highlands, Fair Oaks, Foothill Farms, Granite Bay, and Del Paso Park. If you’re within a reasonable drive of Folsom, we’ll come take a look. Call (833) 589-9896 and we’ll work out a time that fits your schedule.
Serving Folsom, CA – Our Local Coverage Area
We’re based in the Folsom area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Folsom
Chimney repair is any work that restores the structural integrity or safe function of a chimney, including the masonry, crown, flashing, cap, and flue liner. It covers everything from repointing mortar joints to installing a new stainless liner. We sweep, repair, and reline, so one call covers it all.
Most cap replacements, flashing repairs, and crown repairs are completed in a single visit of four to eight hours. Liner installations typically take one full day, and partial masonry rebuilds can run two to three days depending on weather and access. We’ll give you a clear timeline before the work starts.
Most repairs fall between $200 and $4,200 depending on whether it’s a cap, flashing, crown, liner, or masonry work. Smaller jobs like cap replacement start around $200 to $550, while a full DuraFlex liner installation can run $1,800 to $4,200. Call (833) 589-9896 for a free estimate that’s based on your actual chimney, not a price sheet.
Yes. We work with DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield materials, but we service and repair chimneys and fireplaces from all manufacturers. If you have a factory-built fireplace, masonry chimney, or gas insert of any make, we can inspect and repair it.
We prioritize active leaks and structural hazards because water and gravity don’t wait. If your chimney is actively leaking into the house or showing signs of structural failure, call (833) 589-9896 and we’ll get someone out as quickly as the schedule allows. Most non-emergency repairs are booked within one to three weeks.
Our workmanship is done to the material manufacturer’s spec and current code, and the products we install carry their own manufacturer warranties. When a repair is installed correctly using trade-grade materials, the warranty from DuraFlex, HeatShield, or the cap manufacturer covers the product, and we stand behind the installation.
Clear a path to the fireplace and move anything fragile away from the hearth area, but leave the chimney itself alone. Don’t light a fire the day of the appointment, and keep pets out of the room where we’ll be working. We handle everything from ladders to drop cloths.
Schedule Your Chimney Repair Service in Folsom Today
If your Folsom chimney needs repair, the fastest way to a straight answer is a phone call. Reach Alan Decker and the Chimney Sweep Folsom team at (833) 589-9896 for a free, no-obligation estimate. We’ll inspect it, show you what we find, and fix it right with materials built for the job. Your Chimney Repair in Folsom starts with one call.
Written by Alan Decker, Owner at Chimney Sweep Folsom, serving Folsom, CA and the surrounding foothill communities.